Return to Search Results

Toyota Prado (2015 - 2023)

Engine & Transmission Remap

What's Included?

Pre-Tune Health Check
Engine Remap
Transmission (TCU) Remap - Automatic Vehicles only
Before & After Print Out

Model: GDJ150 1GD 2.8lt

Years: 2015 - 2023

Engine & Transmission Remap: $1990.00


Share:
  • addressString

Stage 1

STANDARD
DYNO TUNED
DIFFERENCE

POWER

130

KW

162

KW

32

KW

TORQUE

450

NM

573

NM

123

NM

Toyota Landcruiser Prado 150 Series: 2.8L 1GD-FTV Engine & Transmission Tune
Suits 2.8L 150 Series Prado models.

The 150 Series Prado has long been the Landcruiser families choose for touring, towing and getting well off the beaten track. It’s comfortable enough for the daily run and capable enough for the long haul: a proven, dependable 4WD built to be loaded up and driven hard.

Comfortable and capable isn’t the same as reaching its full potential, though. The 2.8L 1GD-FTV leaves the factory with a conservative calibration, which leaves real, usable performance on the table. With our engine and transmission remap, the Prado pulls harder, responds faster and tows with far less effort.

Engine tune

A properly developed tune sharpens throttle response, lifts power and torque where you actually use them, and makes the Prado easier to drive under load. Our focus is controlled, real-world calibration that keeps the engine working within itself, rather than chasing headline figures at the expense of longevity. It’s the biggest single change you’ll feel, whether you’re towing the van, touring or driving every day.

Transmission tune (automatic models)

Our remap also recalibrates the 6-speed automatic. The factory calibration often hunts for gears, is slow to lock the converter, and never quite settles on the highway. You speed up to coax it into 6th, then ease off and hope it stays there. A small hill or a bit of headwind can be enough to drop it back to 5th or 4th.

Lock-up kits try to work around this with a button that forces the converter to lock. Our remap fixes the calibration itself, so the transmission does the job without one.

Into 6th at 100km/h, and it stays there

With revised shift points, the transmission moves into 6th at highway speed by itself. You don’t need to coax it or manage the throttle.

Earlier torque converter lock-up

The converter now locks earlier in 4th, 5th and 6th gear and stays locked. Less slip gives you a more direct, connected drive and lower transmission temperatures, which matters most when you’re towing a heavy load over long distances.

Downshifts that make sense

Revised downshift speeds mean the transmission holds its gear through gentle hills and headwinds. It drops a gear only when the road actually calls for it.

Line and converter pressure matched to the extra torque

More engine torque needs more clamping force inside the transmission. We raise the transmission line pressure and the torque converter clutch pressure to match the extra torque from the engine remap.

That pressure is what gives the transmission its grip. You get firm, positive shifts and a converter that locks with confidence. Without it, a tuned engine can leave the transmission with soft, slow shifts and clutches that slip, which wears them out sooner. With the pressure set to suit the torque, shifts stay crisp and the gearbox is protected for the long haul.

Done the way Toyota does it

We reprogram the engine and transmission through the OBD port, the same way Toyota does in the factory. There are no chips, piggyback modules or cut wires, and nothing comes out of the vehicle.

What’s included

Pre-tune health check and baseline dyno run

We assess your engine under load, record its data and measure its current power and torque. If we find an issue, you’ll hear about it before we touch the tune, not after.

Fault code scan

We scan for stored and pending fault codes before any tuning starts.

Engine & transmission remap

Our calibration, developed for the 1GD, delivers more power and torque with smooth drivability. On automatic models it also includes the transmission changes described above.

Data logging and dyno testing

We monitor how your engine responds under load throughout the tuning process and verify the results on the dyno.

Post-tune road test

Every vehicle is road-tested before handover so we can check how it drives beyond the dyno.

Before and after dyno printout

You’ll receive a printout showing your power and torque before and after tuning, so you can see the results for yourself.

Talk to the team

If you want more from your Prado, give the team a call to hear what our tune can do for it.

Please note

  • Before and after figures are engine figures. They are calculated by applying the percentage gain achieved on our dyno to the manufacturer’s quoted power and torque, and are based on vehicles running standard wheels and tyres. They are provided as a guide only.
  • Results vary between vehicles depending on kilometres, engine condition, modifications fitted, and wheel and tyre size. The before and after dyno print-outs supplied with each tune show figures measured at the wheels, which will be lower than engine figures. Larger or heavier wheels and tyres will reduce measured figures further.
  • Vehicles must be in good mechanical condition prior to tuning. Increases in power on high-kilometre engines are assessed case by case.
  • Additional parts and labour may be required where worn or faulty components are identified, and these will be quoted before any work proceeds.
  • Prices are subject to change without notice. Images are for illustration purposes only.


You May Also Be Interested In